You searched for - Page 4 of 11 - Applied PI Sand Blasting Machines & Equipment

UniFlo Valve

The Applied UniFlo Control Valve is an air operated inlet/outlet valve utilised to control the supply of compressed air into the blast pot. In its un-activated or closed position, the valve shuts off the compressed air supply to the blast pot, and simultaneously opens the pots outlet port to release any compressed air contained in the blast pot. Operation of the UniFlo Control Valve is via a pilot air signal from the operator depressing the PanBlast AirFlo Control Handle.

Upon receiving a pilot air signal from the depressed AirFlo Handle, the UniFlo Control Valve will instantaneously open, thus permitting the pot to pressurise and supply compressed air to the blast hose. Simultaneously, the UniFlo valve closes the pot outlet port, thus sealing the blast pot.

Tandem Air Control Valve

The Applied Tandem Air Control Valve is a rugged, cast iron, pilot operated, spring return diaphragm type valve, designed for use with blast pot remote control systems. Located in the air pusher line, the tandem valve is used to turn the blasting compressed air supply on and off as required.

When combined with the Applied Corse Abrasive Valve, the tandem valve allows the blast pot to feature an air blow down system where the abrasive flow is shut off and the compressed air supply is used to blow residual abrasive and dust from the blast cleaned component. The tandem valve is available in a variety of sizes.

Sola 5 Remote Control Valve

The Sola 5 Remote Control Valve is a tough, reliable inlet control valve, designed for use in conjunction with a separate exhaust valve, such as the HiFlo exhaust valve (or similar). The Sola 5 valve, along with all replacement parts, is completely interchangeable with the OEM product.

The Sola 10 Valve is a normally closed, spring return type valve. Upon receiving a signal from the dead man control handle, compressed air enters the valve upper cylinder, which forces downwards the piston/plug assembly, thereby opening the control valve. When the separate exhaust valve is operated, the air in the cylinder is exhausted from the valve, and the spring then in turn closes the valve assembly.

Remote Control Valve

The Applied Remote Control Handle, also known as the Deadman’s Handle gives the operator the ability to remotely activate or deactivate the blasting abrasive flow using a pneumatic system. With this ability, productivity will increase dramatically and also reduce costs by controlling when the blast pot shoots out abrasive.

Our control handles feature a spring assisted safety tab to ensure increased safety and eliminate accidental activation of the blast pot. The handle is connected directly to the blast pot control valve using a twinline hose and when the handle is pressed by the operator, the bleed orifice is closed off allowing signal back to the blast pot control valve thus activating the blast pot.

½” BSP Water Separator

Our Applied moisture separators are engineered specifically to remove moisture oil and other unwanted debris from the abrasive blasting air stream. Moisture oil and debris in the blast pot will introduce many problems as the abrasive media will clump and clog the valves, hoses and nozzles increasing downtime and maintenance costs.

Water vapour occurs naturally in air, especially in compressed air but our moisture separators will ensure dry clean compressed air to your blast machine reducing the risk of equipment clogging, excessive wear and additional maintenance. The moisture separators provide extremely high efficiencies even at low velocities. The separator directs the incoming air in a spiral and uses centrifugal force to separate out the water in the compressed air through the filter element.

1” BSP Water Separator

1½” BSP Water Separator

Quick Disconnect Coupling – Male and Adapter

Applied Quick Disconnect Couplings are manufactured and machined from high quality material and are a no spill coupling which will easily and quickly fit onto the airline system.

Our male couplings are designed to quickly slot into the female version by pressing down on the spring loaded band to allow the male disconnect into place.

Quick Disconnect Coupling – Female

Applied Quick Disconnect Couplings are manufactured and machined from high quality material and are a no spill coupling which will easily and quickly fit onto the airline system.

Our fittings feature air tight performance with minimal pressure loss. They are designed with a Push-Pull configuration for quick inspection and maintenance. The couplings also feature a working pressure of 3000psi and a compact envelope.

Filter Adapter Kit

The Applied Respirator Filter Adaptor Kit is specifically designed to replace old filters that suit respirator filters that use flanged style cartridge. This service kit allows operators to benefit from both the cost savings and efficiency advantage of using an Applied Respirator Filter Cartridge.

Search Results: